Copper Cabling · Keystone Jacks
CAT6A UTP 90° RJ45 Keystone Jack
Model: ZC90KJU6A-B4
The ZION ZC90KJU6A-B4 is an unshielded CAT6A RJ45 keystone jack with a 90-degree configuration. Its IDC assembly accepts 22–24 AWG solid wire, while the housing uses new PC material.
CAT6AUTP90° Design22–24 AWG SolidNew PC
Quick Takeaway
- CAT6A UTP RJ45 keystone interface with a 90-degree configuration.
- New PC housing and IDC components.
- RJ45 contact life: 750 cycles minimum.
■1) Product Overview
The ZC90KJU6A-B4 provides an RJ45 connection point for CAT6A unshielded structured cabling. The 90-degree termination arrangement defines this model’s mechanical configuration.
The product uses phosphor bronze terminals and a new PC IDC housing. Select the jack together with compatible solid-conductor cable and a mounting accessory that matches the dimensional drawing.
Key Takeaway: Choose this model when the project calls for a CAT6A UTP keystone jack and 22–24 AWG solid-wire termination. Verify physical fit with the selected faceplate or patch panel.
■2) Key Features
CAT6A UTP Configuration
Unshielded RJ45 keystone jack identified as CAT6A in the supplied datasheet.
90-Degree Design
90-degree configuration.
Solid-Wire Termination
IDC assembly specified for 22–24 AWG solid wire.
New PC Housing
Plastic material specified as new PC.
Phosphor Bronze Terminals
Phosphor bronze is listed for the terminal components.
750-Cycle Contact Life
RJ45 contact life is specified as 750 cycles minimum.
■3) Technical Specifications
| Parameter |
Specification |
| Model |
ZC90KJU6A-B4 |
| Product type |
CAT6A UTP RJ45 keystone jack |
| Configuration |
90 degree |
| Plastic material |
New PC |
| IDC material |
New PC |
| Accepted conductor |
22–24 AWG solid wire |
| Terminal material |
Phosphor bronze |
| RJ45 contact life |
750 cycles minimum |
| IDC life |
Source states “IDN LIFE: 250 TIMES MIN”; terminology requires confirmation. |
| Terminal pin plating |
Source states “ZIN PLATING”; plating type requires confirmation. |
| Contact finish / customization |
Source states “TIN GOLD 3U”, customizable to “50 U”; finish and unit require confirmation. |
| Contact resistance |
Source states “20M OHM”; unit and limit require confirmation. |
| Insulation resistance |
Source states “<= 500M OHM @100 V DC”; inequality and unit require confirmation. |
| Withstand voltage |
DC 1000 V / AC 700 V RMS, 60 Hz, 1 minute |
| Permanent-link reference |
Source states “ANSI/TIA/EIA 568B.2-10”; applicable reference requires confirmation. |
| Storage temperature |
Source states −40° to +70°; temperature unit not explicitly identified. |
| Operating temperature |
Source states −10° to +60; temperature unit not explicitly identified. |
Technical Note: Ambiguous source entries are reproduced above for traceability. Confirm the electrical limits, plating specification, temperature unit and applicable test reference with ZION before using them as project acceptance criteria.
■4) Construction & Design
The housing and IDC components are specified as new PC. The supplied dimensional drawing shows the front, side and top profiles, including the mounting latch and rear termination area. Use that drawing to check the intended mounting opening and available rear clearance.
The source lists a base contact finish of “3U” and a custom option up to “50 U”. Specify the required finish in the inquiry and obtain confirmation of the plating material and thickness unit.
Packing Information
| Parameter |
Specification |
| Individual packing |
1 piece / PE bag |
| Inner box quantity |
100 pieces |
| Carton quantity |
1,000 pieces |
| Box size (L × W × H) |
20.5 × 20 × 11.5 cm |
| Carton size (L × W × H) |
62 × 42 × 23 cm |
■5) Cable & Mounting Compatibility
Cable selection: Match the IDC to 22–24 AWG solid wire. Stranded-conductor compatibility is not specified in the supplied datasheet.
Mounting selection: Check the mating opening, latch engagement and rear clearance against the product drawing. Compatibility with a particular faceplate or patch panel should be verified using a sample.
Project requirements: This is an unshielded model. Confirm any project-specific shielding, electrical testing and installation requirements before ordering.
■6) Applications
Typical intended uses include CAT6A UTP network outlets, compatible modular patch panels and structured cabling termination points in office or commercial installations. These uses depend on the selected cable, mounting hardware and installation requirements.
For project supply, the stated bag, box and carton quantities provide a basis for planning distribution to installers and site teams.
■7) Decision Rules
| Parameter |
Specification |
| Choose this model when |
The required configuration is CAT6A UTP, 90-degree RJ45, with 22–24 AWG solid wire. |
| Check mounting fit when |
Selecting a faceplate, outlet module or blank patch panel. |
| Confirm before specifying |
Electrical resistance limits, plating finish and thickness, temperature unit and test reference. |
| Request a different configuration when |
The project needs shielding or a conductor type outside the stated range. |
■8) Selection Guide
For a quotation or sample request, provide the model ZC90KJU6A-B4, quantity, cable conductor size, mating faceplate or patch panel details, required contact finish and project test requirements.
| Parameter |
Specification |
| 1. Identify the configuration |
Confirm CAT6A UTP and the 90-degree arrangement. |
| 2. Match the conductor |
Use the stated 22–24 AWG solid-wire range. |
| 3. Verify physical fit |
Review the dimensional drawing and evaluate a sample. |
| 4. Resolve specification details |
Confirm ambiguous values against an updated datasheet. |
| 5. Plan packing |
Allow for 100 pieces per box and 1,000 pieces per carton. |
■9) FAQ
Is this keystone jack shielded?
No. ZC90KJU6A-B4 is identified as a UTP, or unshielded, model.
Which wire sizes does the IDC accept?
The supplied datasheet specifies 22–24 AWG solid wire.
What is the housing material?
The plastic material is specified as new PC. The IDC material is also listed as new PC.
What is the specified RJ45 contact life?
The datasheet specifies a minimum of 750 cycles for the RJ45 contacts.
Can the contact finish be customized?
The source lists a standard “3U” finish and customization up to “50 U”. Confirm the plating material and unit with ZION when requesting a quotation.
How is the product packed?
Standard packing is 1 piece per PE bag, 100 pieces per box and 1,000 pieces per carton. The box measures 20.5 × 20 × 11.5 cm; the carton measures 62 × 42 × 23 cm.
■10) Conclusion
The ZION ZC90KJU6A-B4 combines a CAT6A UTP RJ45 interface, a 90-degree configuration and 22–24 AWG solid-wire termination. Its specified PC housing and standard bulk packing make it a candidate for compatible structured cabling installations.
Discuss Your CAT6A Keystone Jack Requirements
Send ZION your required quantity, cable details, mounting accessory and contact finish specification to request an updated datasheet, sample or quotation.
Request Datasheet / Sample